PART OF THE SMARTLIFEITEMS NETWORK · SMARTLIFEITEMS · RESTRIGHT · HAPPYPAWS · MIGRAINEEASE · OUTDOORHIKING

What Is an Arc Fault on a Solar System: Loose Joints, Noise Signatures, and Finding the Cause

An arc fault is current jumping a gap it should not have to cross, and the inverter detects it by listening for the electrical noise that arcing produces. An arc fault on a solar system nearly always traces back to one loose, corroded, or badly made connection somewhere in the DC wiring.

The detection circuit is called an AFCI, and it shuts the system down rather than reducing output. Our note on where solar fire risk actually sits covers why direct current arcs behave the way they do.

Quick Answer

Arc fault detection listens for the high-frequency noise signature of an arcing DC circuit. A loose connector, an under-torqued terminal, or a poor crimp creates a small gap that current arcs across. The fault is a real hazard indicator, and the joint is what needs finding.

Key Points

  • The inverter detects a noise signature, not heat or current loss.
  • A series arc means a break in the current path, usually a joint.
  • A parallel arc means failed insulation between conductors.
  • Series arcs are more likely at high current, so midday trips are a clue.
  • Connectors and terminals cause the large majority of these faults.
  • Thermal imaging under load is the most direct way to find a bad joint.
  • Nuisance trips exist, but repeated trips are not nuisance trips.
Arc typeWhat creates itWhere to look first
Series arcA gap in the current path carrying full string currentConnectors, terminals, junction boxes
Parallel arcFailed insulation between two conductorsPinched or abraded cable runs
Unseated connectorA pair pushed together without latchingAny connection made in awkward access
Mismatched connectorsDifferent brands that click but contact poorlyRepairs and later additions to the array
Bad crimpInsufficient compression on the conductorField-made cable ends
Loose terminal screwUnder-torqued at install, or loosened by cyclingCombiner box, disconnect, inverter terminals
Corroded contactWater and years of temperature swingsOlder connections, low points, shaded runs

What the Inverter Is Detecting

An arc generates electrical noise across a wide band of frequencies, and that noise travels back along the DC conductors. The AFCI circuit watches for that signature rather than for a change in output.

This matters because an arcing joint can be invisible in production data. The current still flows, the power still arrives, and nothing looks wrong on a monitoring screen.

So arc fault detection catches a class of problem that no output measurement would reveal until something had already failed or burned.

It also means the inverter stops rather than derates. Arc detection is a trip, not a reduction, and the system stays down until the fault is cleared and reset.

Series Against Parallel Arcs

A series arc sits in the current path itself. A joint loosens until there is a microscopic gap, and the full string current arcs across it every moment the array is producing.

That is the common case in solar, because a DC array has many mechanical joints carrying current continuously for decades.

A parallel arc happens between two conductors, or between a conductor and ground, through insulation that has failed. This overlaps with ground fault territory and often shows as both.

The distinction is useful for the search. A series arc is at a joint. A parallel arc is along a cable run.

Where the Loose Joint Usually Is

Connectors that were never fully seated

A connector pair pushed together without latching looks connected and makes partial contact. Connections made lying on a roof, reaching under an array, are the ones this happens to.

Mismatched connector brands

Different manufacturers’ connectors physically mate and click. The internal contact geometry does not match, so the contact area is small and the resistance is high.

Field crimps

A crimp made with pliers rather than the correct die works at first and degrades. Our roundup of MC4 tools and crimpers covers the tooling this depends on.

Terminal screws

Terminals in combiner boxes, disconnects and inverters have torque specifications for a reason. Our roundup of torque tools for solar terminals covers hitting them.

Why Solar Has So Many Candidates

The reason arc faults get their own detection circuit in solar becomes obvious once you count the joints. A residential array carries dozens of mechanical DC connections, and a larger one carries hundreds.

Almost all of them were made in the field, outdoors, often by someone reaching over a rail or lying on a roof. Household AC wiring concentrates its joints inside boxes in conditioned space.

Those connections then sit through temperature cycling every day for decades. Metal expands and contracts, and a joint that was only just tight enough works itself looser over years rather than weeks.

So the population of possible arc sites is large, exposed, and slowly degrading, which is a different situation from indoor wiring. That is the case for detection rather than inspection alone.

Nuisance Trips Are Real, and Rare

AFCI detection works on a noise signature, and other things make noise. A single unexplained trip after a storm, or alongside heavy electrical work nearby, can be exactly that.

Some equipment on the array also produces noise deliberately. Rapid shutdown devices and module-level electronics communicate over the DC conductors, and interaction between that communication and arc detection has caused false trips on some equipment pairings.

Our roundup of rapid shutdown devices covers that category of hardware.

The honest framing is that one trip is ambiguous and a pattern is not. A system tripping repeatedly, especially around the middle of the day when current is highest, is reporting a real joint.

Treating a recurring trip as a nuisance is how a genuinely bad connection gets left in place for another season.

How an Arc Fault Gets Found

  1. Log the trips against time of day. Midday clustering points to a series arc at high current.
  2. Thermal image the array under load. A resistive joint runs hotter than its neighbors, which is the most direct evidence available.
  3. Inspect connectors visually. Look for discoloration, deformation, or melted plastic at the housing.
  4. Check for mixed connector brands. Any repair or later addition is a candidate.
  5. Shut down safely, then torque-check terminals. AC first, then DC, then verify nothing is energized.
  6. Replace suspect connectors rather than reseating them. A connector that has arced is damaged inside.
  7. Re-torque and document. Recording what was checked stops the same joints being checked twice.

Our roundup of thermal cameras for solar inspection covers the imaging side, and our roundup of solar connectors and cables covers replacement parts that match what is already installed.

Recommended Reading

Frequently Asked Questions

What is an arc fault on a solar system?

It is current arcing across a gap in the DC wiring where there should be solid contact. The inverter’s arc fault detection listens for the electrical noise that arcing produces and shuts the system down. The underlying cause is usually one loose connector, poor crimp, or under-torqued terminal.

How is an arc fault different from a ground fault?

They are different measurements. Arc fault detection listens for the noise signature of arcing, typically at a joint in the current path. Ground fault detection measures insulation resistance and leakage toward ground, typically caused by damaged cable or water in an enclosure. A failing cable run can trigger both.

Why does it trip around midday?

Because a series arc is current-dependent. The joint that arcs weakly at low morning current arcs strongly when the array is at full output. Trips clustering in the middle of the day are strong evidence of a resistive joint rather than of an electrical noise problem.

Can I just reset it?

Once, to see whether it recurs. Not as a routine. Arc fault detection exists because a sustained DC arc can start a fire, and the reset clears the message rather than the joint. A system that needs resetting repeatedly has a connection that needs replacing.

Are nuisance trips common?

Less common than people hope. Genuine false trips happen, sometimes from external electrical noise or from interaction between module-level communication and the detection circuit. A single isolated trip may be one. A recurring pattern should be treated as a real fault until inspection says otherwise.

How do you find the bad connection?

Thermal imaging under load is the most direct method, because a high-resistance joint runs hot. Visual inspection for discolored or deformed connector housings comes next, followed by a torque check of every accessible terminal with the system safely shut down.

Can I reuse a connector that arced?

No. Arcing erodes the contact surfaces and can distort the housing, so a connector that has arced has higher resistance than it started with even after reseating. Replace both halves of the pair, and match the brand to what is already in the string.

Does this need an electrician?

Reviewing trip times and looking for visible damage from a safe position does not. Opening enclosures, disconnecting connectors, or torque-checking terminals does, because a DC array is energized in any daylight and a DC arc does not self-extinguish. That work belongs with a qualified person.

Keep Reading

Related guides