Because something differs between them, and whether the gap is in current or in voltage tells you which category of cause to look at. When one solar string produces less than another, that single distinction cuts the search roughly in half before you touch anything.
Low current points at light reaching the panels. Low voltage points at the panels or their internals. Our roundup of clamp meters for DC solar covers the instrument that separates them.
Quick Answer
Compare string current and string voltage rather than just output. A current gap with matching voltage means shading, soiling, or a mismatched panel count. A voltage gap with matching current means a module problem, most often a shorted bypass diode. Time of day separates shading from hardware.
Key Points
- Confirm the strings are meant to match before diagnosing anything.
- Series strings run at the current of their weakest module.
- A current gap points to light: shading, soiling, panel count.
- A voltage gap points to hardware inside a module.
- Shading follows a daily clock. A hardware fault does not.
- A shorted bypass diode causes voltage loss with no visible damage.
- Swapping strings between inputs proves whether the inverter is involved.
| What you measure | Points to | Next step |
|---|---|---|
| Lower current, voltage matches | Shading, soiling, or fewer panels | Walk the array at the time the gap appears |
| Lower voltage, current matches | A module or a bypass diode | Measure open-circuit voltage per module |
| Both lower | Mismatched string build, or two faults | Recount panels and confirm the model |
| Gap only in the morning | East-side obstruction | Look for what casts shade at that hour |
| Gap only in late afternoon | West-side obstruction | Same, from the other direction |
| Gap constant all day, every day | Hardware, not shading | Isolate and measure rather than inspect |
| Gap grows as the day gets hotter | A high-resistance connection | Thermal image the string under load |
| Gap follows the string when swapped inputs | The string | Continue in the array |
First, Confirm They Should Match
A surprising share of these questions resolve here. Strings facing different directions, or at different tilts, are supposed to produce differently and at different times of day.
Panel count is the next check. A string with one fewer module in series produces proportionally less voltage, and nothing is wrong with it.
Panel model matters too. Strings built at different times, or repaired with what was available, can hold modules with different ratings.
So the first job is establishing what the design intended. Diagnosing a difference that was designed in wastes a weekend.
Commissioning records settle this faster than anything else. A gap that has been there since the system was switched on is a build difference, while a gap that appeared later is a fault.
That distinction is worth writing down at handover, because nobody remembers it three years later. Our note on commissioning a new solar system covers what to capture.
Low Current Against Low Voltage
Why current behaves this way
Modules wired in series all carry the same current, and that current is set by the least productive module. One shaded or soiled panel pulls the whole string down with it.
What a current gap means
Something is limiting light on at least one module in that string. Shade, dirt, a bird dropping, or debris sitting on a panel all produce this.
Why voltage behaves differently
Voltages in series add, so string voltage reflects how many modules are contributing and how much each contributes. Losing part of a module’s contribution shows as a voltage gap.
What a voltage gap means
Usually something inside a module rather than on top of it. Our note on signs a solar panel is failing covers the module-level symptoms.
Shading Has a Clock, Hardware Does Not
This is the most useful pattern in the whole diagnosis, and it costs nothing to check. Shading arrives and leaves at predictable times because the sun moves predictably.
A string that matches its neighbor at midday and falls behind at four in the afternoon is being shaded from the west. The obstruction may be a vent, a chimney, a parapet, or a tree that was smaller when the system went in.
A hardware fault produces a gap that is there whenever the array is producing, in roughly the same proportion, regardless of the hour.
Seasonal drift is worth noting too. An obstruction that clears the array in summer can shade it in winter when the sun sits lower, which is why a gap appearing in autumn is often shade rather than a failure.
Our note on how much shade affects solar panels covers why the penalty is so disproportionate on a series string.
The Bypass Diode Case
This is the fault people miss, because it presents with nothing to see. A module contains bypass diodes that let current route around a shaded or damaged section rather than forcing it through.
When one of those diodes fails short, it conducts permanently. Current still passes, so the string keeps working, but the section behind the diode stops contributing voltage.
The result is a string running at normal current and reduced voltage, with a module that looks perfectly intact from the roof.
Finding it means measuring open-circuit voltage module by module with the string safely isolated. The one that reads low against its identical neighbors is the one.
Our roundup of junction boxes and bypass diodes covers the component, and our guide to testing a solar panel with a multimeter covers taking the measurement.
Narrowing It Down
- Recount and confirm the build. Panel count, model, orientation, tilt, on both strings.
- Log the gap against time of day. Over several clear days, not one.
- Clamp each string’s current under steady sun. Measure both within the same minutes or the comparison means nothing.
- Read each string’s voltage at the same time. This is the fork that directs everything after it.
- Swap the two strings between inverter inputs. If the gap moves with the string, the array owns it.
- For a voltage gap, measure per module. With the system safely shut down and isolated.
- For a current gap, walk the array at the hour the gap appears. Shade is obvious when you look at the right time.
Doing any of this comfortably depends on the combiner being built for it, and our roundup of solar combiner boxes covers that. Everything involving disconnection or per-module measurement is licensed work on a circuit that is energized in any daylight.
Related Reading
Frequently Asked Questions
Why is one solar string producing less than another?
Because something differs between them, and the useful first question is whether the gap is in current or voltage. A current gap means light is being limited, usually by shade, soiling or a smaller panel count. A voltage gap means something inside a module, most often a shorted bypass diode.
Should identical strings produce identical output?
Close, but never exactly equal. Small manufacturing variation between modules, minor differences in temperature across a roof, and slight orientation differences all produce a small spread. A gap of a few percent between matched strings is ordinary. A gap you can see at a glance is not.
How does one shaded panel affect a whole string?
Modules in series all carry the same current, and that current is set by the weakest one. So a single shaded module limits every module behind it, which is why the loss is far larger than the shaded area would suggest. Optimizers and microinverters exist to break that dependency.
What is a shorted bypass diode?
A bypass diode routes current around a damaged or shaded section of a module. When one fails short, it conducts permanently, so that section stops contributing voltage while current still flows normally. The module looks undamaged, which is why this fault is usually found by measurement rather than inspection.
How do I know whether the inverter is at fault?
Swap the two strings between the inverter’s inputs, with the system safely shut down first. If the lower reading stays with the same physical string, the cause is in the array. If it stays with the same input, the inverter or that input is involved.
Why would the gap get worse in the afternoon?
Two different reasons, and they are distinguishable. Shade from the west arrives at a predictable hour and the gap appears suddenly. A high-resistance connection worsens as current rises and as the joint heats, so that gap grows gradually through the day rather than appearing at a time.
Can soiling really cause this?
Yes, especially uneven soiling. Dust building along a lower edge, a bird dropping on one cell, or debris shed by a nearby structure onto one section of the array all limit current on that string. This is one of the few causes that a wash will confirm or eliminate within an afternoon.
When does this need an electrician?
Reading monitoring data, logging patterns, and looking at the array from a safe position do not. Clamping string currents inside a combiner, disconnecting strings, swapping inputs, or measuring per module all do, because those circuits are live at array voltage whenever there is daylight.